好的,所以您最近才购买了一台新的Surface设备,或者您已经有一段时间了,并且由于一些奇怪但未知的原因,可能在Windows更新后,显示器没有旋转。我们知道,您的Surface设计用于在您转动屏幕时旋转屏幕上的内容,这与您的智能手机相同。现在,当屏幕无法按预期旋转时,许多用户首先想到的可能是产品有缺陷。
Surface 屏幕不旋转
在大多数情况下,情况并非如此。旋转(Rotation)依赖于软件;因此,我们可以假设在您不知情的情况下对 Windows 10 进行了更改,导致轮换失败。我们将研究一些选项,以便您确定是什么原因,所以请继续阅读,女士们,先生们。
如何使Surface屏幕自动旋转
如果Surface(Surface)设备的屏幕没有自动旋转,请尝试以下建议来修复Surface自动旋转问题:
- 移除Surface Cover或任何外部屏幕
- 看看自动旋转设置(Auto Rotation Settings)
- 重新启动 Surface
- 安装最新的 Windows 10 和固件更新
- 运行传感器疑难解答
- 恢复 Surface。
1]移除(Remove)Surface Cover或任何外部屏幕
当连接Surface打字机盖或外接显示器时,屏幕会一直停留在横向模式。现在,为了让物体旋转,最好的选择是断开Surface外壳或外接显示器。
完成这些操作后,检查您的显示器现在是否自动旋转而没有任何问题。
2]看看自动旋转设置(Auto Rotation Settings)
如果您仍然遇到问题,那么可能与自动旋转设置有很大关系。要检查这一点,请取下盖子,然后从屏幕右边缘滑动以显示操作中心(Action Center)。
从这里,您应该会看到Auto Rotation lock,如果它变暗,则表示它已停用。要激活它,请用手指或鼠标点击锁,这样就可以了。
请注意,一旦连接Surface Cover(Surface Cover)并处于打字位置,自动旋转就会自动锁定。除非它首先被锁定,否则向后折叠盖子应该会激活自动旋转。
3]重新启动你的表面
我们在这里拥有的是与Windows 10相关的任何事情的基本修复之一。在大多数情况下,简单地重新启动计算机就足以完成工作,所以这就是我们现在要做的,好吗?好(Good)。
要关闭计算机,请单击Windows按钮,然后导航至Power > Shut关机。Surface关闭后,请按物理电源按钮使其重新启动并运行。从那里,然后检查旋转是否正常工作。
4]安装最新的Windows和固件更新
您的计算机上可能未安装最新版本的Windows 11/10和Surface 驱动程序和固件;(Surface drivers & firmware)因此,我们必须解决这个问题。请记住(Bear),您的Surface电脑需要固件和 Windows 11/10 更新才能保持最佳性能。
在Surface(Surface)上更新 Windows 11/10 操作系统很简单。只需(Just)点击WinKey + I启动设置(Settings)应用程序,然后导航到更新(Updates)和安全(Security)。最后(Finally),点击Windows Update > Check for Updates,就是这样。
5]运行传感器故障排除程序
运行疑难解答非常简单。只需(Just)打开Sensors Troubleshooter,然后按照显示屏上的说明进行操作,仅此而已。
6]恢复你的表面
今天的最后一步,应该永远是最后的手段,就是将你的Surface电脑恢复到以前的状态。请记住(Bear),恢复可能会删除最近安装的应用程序和驱动程序,所以在继续之前请记住这一点,老朋友。
要将Surface恢复到以前版本的Windows 10,请导航至Select Start > Settings > Update和Security > Recovery。您现在必须进入“返回到以前版本的Windows 10 ”部分,然后单击“开始(Get Started)”以开始该过程。
阅读下一篇(Read next):屏幕自动旋转在 Windows 表格模式下不起作用或灰显(Screen Auto-Rotation not working or grayed out in Windows Table Mode)。
Microsoft Surface screen is not rotating
OK, so you only recently purchased a new Surfaсe device, or you had one for quite somе time now, and for some odd, yet unknown reason, maybe after Windows update, the display is not rotating. We know that your Surface was dеsigned to rotate content оn the screen whenever you twist and turn it, which is the same as your ѕmartphone. Now, when the screen fails to rotate as expected, the first thing on the minds of many uѕers, is probably the prоduct is defective.
Surface screen is not rotating
In most cases, this is not the case at all. Rotation relies on the software; therefore, we can assume that changes were made to Windows 10 unknowing to you that caused the rotation to fail. We are going to look into a few options in order for you to determine what is the cause, so keep reading, ladies and gentlemen.
How to make Surface screen auto-rotate
If the screen of your Surface device is not rotating automatically, then try the following suggestions to fix Surface auto-rotation problems:
- Remove the Surface Cover or any external screen
- Take a look at the Auto Rotation Settings
- Restart your Surface
- Install the latest Windows 10 and firmware updates
- Run the Sensors Troubleshooter
- Restore your Surface.
1] Remove the Surface Cover or any external screen
When the Surface typing cover is attached, or an external display, the screen is stuck in landscape mode for the entire time. Now, in order to get things to rotate, the best option is disconnecting either the Surface cover or the external display.
After doing these things, check if your display now autorotates without any issues.
2] Take a look at the Auto Rotation Settings
If you are still having problems, then maybe it has much to do with the auto-rotation settings than anything else. To check on this, please remove the cover, and swipe from the right edge of the screen to reveal the Action Center.
From here, you should see the Auto Rotation lock, and if its dimmed, then that means it’s deactivated. To activate it, tap the lock with your finger or mouse, and that should do it.
Note that auto-rotation locks automatically once the Surface Cover is attached and is in typing position. Folding back the cover should activate the auto-rotation unless it’s locked in the first place.
3] Restart your Surface
What we have here is one of the basic fixes of anything that has to do with Windows 10. In most cases, a simple restart of the computer is good enough to get the job done, so that’s what we’re going to do right now, OK? Good.
To turn off your computer, click on the Windows button, then navigate to Power > Shut down. After the Surface is down, please press the physical power button to get it up and running again. From there, then check to see if the rotation is working as it should.
4] Install the latest Windows and firmware updates
Chances are, the latest version of Windows 11/10 and Surface drivers & firmware is not installed on your computer; therefore, we have to fix that. Bear in mind that your Surface computer requires both firmware and Windows 11/10 updates to stay at optimal performance.
Updating your Windows 11/10 operating system on Surface is simple. Just click on the WinKey + I to fire up the Settings app, then navigate to Updates & Security. Finally, click on Windows Update > Check for Updates, and that’s it.
5] Run the Sensors Troubleshooter
Running the troubleshooter is super easy. Just open the Sensors Troubleshooter, then follow the instructions on your display, and that’s it for that.
6] Restore your Surface
The final step today, which should always be a last resort, is restoring your Surface computer to how it was before. Bear in mind that restoring could remove recently installed apps and drivers, so please keep that in mind before going any further, old chum.
To restore your Surface to a previous version of Windows 10, please navigate to Select Start > Settings > Update & Security > Recovery. You must now go under the section that says Go back to the previous version of Windows 10, and click on Get Started to begin the process.
Read next: Screen Auto-Rotation not working or grayed out in Windows Table Mode.