在今天的帖子中,我们将尝试向您展示如何解决该问题当前的 BIOS 设置不完全支持(The current BIOS setting do not fully support the boot device)您在 Windows 10 计算机上可能遇到的启动设备。
当前BIOS设置不完全支持引导设备
如果您遇到此问题,我们建议您按顺序尝试这些解决方案:
- 物理检查您的硬盘
- 执行启动修复
- 检查引导设备顺序
- 重置 BIOS 设置。
现在,让我们详细看看列出的故障排除。
1]物理检查您的硬盘
此解决方案要求您打开计算机并断开并重新连接内部硬件。仅当您知道自己在做什么或将计算机交给硬件技术人员执行该过程时才继续。(Proceed)
如果这是一个新的或相对较新的版本,请检查HDD是否存在连接问题。打开计算机并断开SATA电缆与HDD和主板的连接。此外,断开HDD的所有电源并让组件闲置几分钟。现在插入所有电缆并将硬盘驱动器连接到主板。启动计算机并查看问题是否已解决。
如果这不起作用,请尝试将HDD插入(HDD)MOBO上的不同SATA端口,看看是否有帮助。
2]执行启动修复
请执行下列操作:
- 插入Windows 10 installation DVD/USB并重新启动计算机。
- 使用Windows DVD/USB或系统修复光盘(System Repair Disc)启动计算机后,会出现一个黑屏,并带有灰色文本“ Press any key to boot from CD or DVD”。按(Press)任意键。
- 选择正确的时间和键盘(Keyboard)类型。
- 单击 左下角的修复计算机 。(Repair your computer )
- 从选择一个选项屏幕中选择疑难解答 。(Troubleshoot )
- 单击 疑难解答屏幕中的高级选项 (Advanced options )。
- 单击Automatic/Startup Repair.
然后 Windows 将在硬盘驱动器上查找问题并验证所有必需的文件是否完好无损。
3]检查启动设备优先级
- 启动计算机并在初始启动屏幕期间按ESC/F1/F2/F8 或F10进入BIOS 设置(BIOS Setup)屏幕
- 选择进入 BIOS 设置选项。
- 由于鼠标不起作用,请使用箭头键进行导航。
- 转到 引导(Boot) 选项卡。
- 现在检查引导设备顺序(check the boot device order)。确保您的HDD被选为优先设备。
- 退出并重新启动计算机。
检查错误是否已解决。如果没有,请继续下一个解决方案。
4]重置BIOS设置
要重置 BIOS 设置,请执行以下操作:
- 重新启动计算机并在启动过程中反复按 ESC/F1/F2/F8 或 F10 以进入BIOS。
- 如果您使用的是Windows 10,请单击 开始(Start) 并选择 电源。(Power.)
- 现在按住 Shift 键并按 重新启动。(Restart.)
- 转到 Troubleshoot > Advanced Options > UEFI Firmware Settings ,然后单击 重新启动。(Restart.)
- 进入 BIOS 后,按 F9 打开 Load Default Options 对话框。
- 使用箭头键选择 Yes将(Yes)BIOS设置重置为出厂默认设置。
- 退出并重新启动计算机。
启动时,检查BIOS错误是否已解决。
这就是成功解决问题的全部内容。(That’s all there’s to successfully resolving the issue.)
The current BIOS setting do not fully support the boot device
In today’s post, we will attempt to shоw you how to resolve the issue The current BIOS setting do not fully support the boot device that you might encounter on your Windows 10 computer.
The current BIOS setting do not fully support the boot device
If you’re experiencing this issue, we suggest you try these solutions in no particular order:
- Check your HDD physically
- Perform Startup Repair
- Check boot device order
- Reset BIOS settings.
Now, let’s take a detailed look at the listed troubleshooting.
1] Check your HDD physically
This solution requires you to open the computer and disconnect and reconnect the hardware inside. Proceed only if you know what you are doing or take the computer to a hardware technician to perform the procedure.
If this is a new or relatively new build, check the HDD for connection issues. Open the computer and disconnect the SATA cable from the HDD and motherboard. Also, disconnect all the power from the HDD and leave the components idle for a few minutes. Now plug all the cables and connect the hard drive to your motherboard. Boot the computer and see if the issue is resolved.
If that does not work, try plugin the HDD to a different SATA port on the MOBO to see if that helps.
2] Perform Startup Repair
Do the following:
- Insert the Windows 10 installation DVD/USB and restart your computer.
- After you boot your computer using Windows DVD/USB or System Repair Disc, a black screen appears with gray text “Press any key to boot from CD or DVD”. Press any key.
- Select the correct time and Keyboard type.
- Click Repair your computer in the lower-left corner.
- Select Troubleshoot from Choose an option screen.
- Click Advanced options in Troubleshoot screen.
- Click Automatic/Startup Repair.
Windows will then look for problems on the hard drive(s) and verify that all required files are intact.
3] Check boot device priority
- Start the computer and press ESC/F1/F2/F8 or F10 during the initial startup screen to enter the BIOS Setup screen
- Choose Enter BIOS setup option.
- Since the mouse does not work, use the arrow keys to navigate.
- Go to the Boot tab.
- Now check the boot device order. Make sure your HDD is selected as the priority device.
- Exit and restart the computer.
Check if the error is resolved. If not, proceed with the next solution.
4] Reset BIOS settings
To reset the BIOS settings, do the following:
- Restart your computer and repeatedly press ESC/F1/F2/F8 or F10 during the startup to get into BIOS.
- If you are using Windows 10, click on Start and select Power.
- Now press and hold the Shift key and press Restart.
- Go to Troubleshoot > Advanced Options > UEFI Firmware Settings and click on Restart.
- Once you are in BIOS, press F9 to open the Load Default Options dialogue box.
- Select Yes using the arrow keys to reset BIOS settings to factory default.
- Exit and restart the computer.
On boot, check to see if the BIOS error is resolved.
That’s all there’s to successfully resolving the issue.