将 AirPods 连接到Apple Watch是有史以来最简单的事情。您不必手动操作。如果您的 AirPods 已连接到您的 iPhone 或 iPad,它将自动与您的Apple Watch配对。但是,有时事情并没有按应有的方式进行。
如果您的AirPods 未与(AirPods are not connecting)Apple Watch连接或配对,请尝试本文中列出的故障排除检查。
在继续之前,请确保AirPods靠近您的Apple Watch。此外,请确认AirPods 的电池电量充足(AirPods hold sufficient battery power)。否则,请将两个AirPods都放入充电盒并将充电盒插入电源。
如果您的AirPods机型支持无线充电,并且您有无线充电器,请将其放在充电板上约 10 分钟。充电一段时间后,尝试将AirPods重新连接到您的设备。(AirPods)
1.禁用飞行模式
启用飞行模式(Airplane Mode)可能会阻止您的 AirPods 连接到Apple Watch(Apple Watch)。如果您的手表正面或屏幕顶部有飞机图标,请转到设置(Settings)>飞行模式(Airplane mode)并关闭飞行模式(Airplane mode)。
您还可以从 Apple Watch 的控制中心禁用(Control Center)飞行模式(Airplane Mode)。按下(Press)数字表冠以(Digital Crown)转到手表的正面并从屏幕底部向上滑动。然后,点击橙色飞机图标(orange airplane icon)以禁用飞行模式。
如果您之前已将 AirPods 与Apple Watch配对(检查设置(Settings)>蓝牙(Bluetooth)),它应该会在禁用飞行模式(Airplane Mode)后连接到您的设备。
要连接新的AirPods,请将它们放入充电盒并打开盖子。接下来(Next),按住机箱上的设置按钮将其置于配对模式。之后(Afterward),打开 Apple Watch 上的设置(Settings)应用程序,点击蓝牙(Bluetooth)并在设备列表中选择 AirPods。
2. 重新启用您的Apple Watch 蓝牙(Apple Watch Bluetooth)
如果关闭飞行模式(Airplane Mode)不能解决问题,则应禁用并重新启用蓝牙(Bluetooth)。打开设置(Settings)应用程序,选择蓝牙(Bluetooth),然后关闭蓝牙(Bluetooth)。
等待(Wait)几秒钟,然后重新打开蓝牙(Bluetooth)。
如果AirPods(AirPods)仍未连接到您的Apple Watch,请继续执行下一个解决方案。
3.断开 AirPods(Disconnect AirPods)与其他设备的连接
如果 AirPods正在被另一台设备(尤其是非 Apple 设备)使用,您可能无法将其与Apple Watch配对。(Apple Watch)断开 AirPods 与您的设备的连接,然后尝试再次将其连接到您的Apple Watch。
在 iPhone 或 iPad 上,前往“设置”(Settings),选择“蓝牙(Bluetooth)” ,点击AirPods 旁边的信息图标 ((info icon () 🛈 ) ,然后选择“())断开连接(Disconnect)” 。
如果AirPods已连接到您的Mac,请单击菜单栏上的蓝牙图标,然后单击 AirPods 的名称以将其与(Bluetooth icon)Mac断开连接。
如果您在 Windows PC 上使用 AirPods(use the AirPods on a Windows PC),请转到设置(Settings)>设备(Devices)>蓝牙和其他设备(Bluetooth & other devices),然后在“音频”部分选择AirPods。之后(Afterward),单击断开连接(Disconnect)按钮。
4. 忘记iPhone 或Apple Watch上的(Your)AirPods
如果之前配对的AirPods(AirPods)不再连接到您的Apple Watch ,请按照以下步骤操作。为此,请从 iPhone 或Apple Watch的内存中移除(Apple Watch)AirPods ,然后重新配对设备。
在 Apple Watch 上忘记 AirPods(Forget AirPods on Apple Watch)
如果您的Apple Watch已与您的 iPhone 配对,忘记手表上的 AirPods 也会从您的 iPhone 和连接到您的 iCloud 帐户的其他设备中删除 AirPods。
- 打开Apple Watch上的(Apple Watch)“设置”(Settings)应用,然后选择“蓝牙(Bluetooth)” 。
- 点击AirPods 名称右下角的信息图标 (🛈) 。(info icon (🛈))
- 选择忘记设备(Forget Device)。
- 您将收到确认提示,通知您从Apple Watch中移除 AirPods 也会从连接到您的 iCloud 帐户的其他设备中移除 AirPods。点击忘记设备(Forget Device)以继续。
等待(Wait)30 秒到一分钟,然后将AirPods重新连接到Apple Watch。
- 将(Place)两个AirPods放入充电盒并打开盖子。按住充电盒背面的设置按钮,直到状态指示灯呈白色闪烁。
- 打开Apple Watch上的(Apple Watch)设置(Settings)应用程序,选择蓝牙(Bluetooth),然后在可用设备列表中选择您的AirPods。请注意 AirPods 名称下方的“未配对”状态描述。
或者,转到手表的表面,从显示屏底部向上滑动,点击AirPlay 图标(AirPlay icon)并选择连接设备(Connect a Device)。这会将您重定向到 watchOS蓝牙(Bluetooth)菜单。
- 等到(Wait)您在 AirPods 名称下方看到“已连接”状态描述。
在 iPhone 或 iPad 上忘记 AirPods(Forget AirPods on iPhone or iPad)
如前所述,从Apple Watch中移除(Apple Watch)AirPods也会将其从 iPhone 或 iPad 中移除。因此,您可以直接从Apple Watch或 iPhone/iPad忘记AirPods 。它会产生类似的结果。如果您选择后者,请按以下步骤操作:
- 打开iPhone 或 iPad 上的设置应用程序,选择(Settings)蓝牙(Bluetooth),然后点击AirPods 旁边的信息图标 🛈 。(info icon 🛈)
- 滚动到AirPods菜单的底部,然后选择忘记此设备(Forget This Device)。
- 在确认提示中选择忘记设备。(Forget Device)
- 再次,在第二个确认提示中选择忘记设备。(Forget Device)
- 要将AirPods重新连接到您的 iPhone 或 iPad,请将两个AirPods都放入充电盒中,并按住充电盒上的设置按钮,直到指示灯呈白色闪烁。
- 您应该会在 iPhone 或 iPad 的底部看到设置动画。点击连接(Connect)以继续。
如果您的设备上未显示AirPods设置动画,请前往“设置”(Settings ) > “蓝牙(Bluetooth)”并在“其他设备(Devices)”部分选择您的 AirPods。
5.重启Apple Watch
您的Apple Watch出现问题?重新启动设备可能会解决问题。按住Apple Watch的侧边按钮并将关闭电源(Power Off)滑块向右移动。
等待(Wait)大约一分钟,让设备完全关闭。然后(Afterward),按住侧边按钮,直到Apple标志出现在Apple Watch上。
6. 取消配对并重新配对您的 Apple Watch(Re-pair Your Apple Watch)
此Reddit(Reddit)线程中的一些用户通过取消Apple Watch与设备的配对来解决AirPods无法连接的问题。请注意,取消配对Apple Watch会将其恢复为出厂设置。有趣的是,来自Apple Watch的数据会自动备份到您的 iPhone 或 iPad。
请按照以下步骤了解如何在将Apple Watch重新(Watch)连接到设备时取消配对并恢复数据。
- 在 iPhone 或 iPad 上打开Watch应用,然后转到我的手表(My Watch)选项卡。
- 选择左上角的所有手表。(All Watches)
- 点击手表旁边的信息图标🛈 。(info icon 🛈)
- 轻点“取消配对 Apple Watch(Unpair Apple Watch) ” 。
- 再次,在确认中选择取消配对 Apple Watch(Unpair Apple Watch)。
- 输入(Enter)您的Apple ID密码,然后点击取消配对(Unpair)以继续。
取消Apple Watch与设备的配对需要一段时间,因此您可能需要等待几分钟。
- 要重新配对您的Apple Watch,请打开Watch应用并轻点“开始配对(Start Pairing)”按钮。
注意:(Note:) 确保(Make)您的 iPhone/iPad 和Apple Watch就在附近。
- 如果您要配对您的个人Apple Watch ,请选择“为我自己设置”;(Set Up for Myself)如果您要为没有 iPhone 或 iPad 的家庭成员设置Apple(Apple Watch) Watch,请选择“为家庭成员设置”。(Set Up for a Family Member)
- 将取景器与(Align)Apple Watch上的配对动画对齐,然后等待大约 2-5 秒。这将立即配对两个设备。
- 由于您正在将手表与 iPhone 重新配对,因此请选择从备份(Restore from Backup)恢复以恢复 Apple Watch 的数据。
- 从列表中选择一个备份,然后点击继续(Continue)以继续。
- 接受使用条款和条件,并按照提示设置Apple Watch到您的偏好——创建密码、设置Siri、调整文本大小、个性化钟面等。
- 您的 iPhone 将与您的Apple Watch(Apple Watch) 同步并恢复您的备份。等到您在(Wait)Apple Watch的屏幕上收到“您的手表(Your Watch)已准备就绪”消息。
(Pair)将AirPods与您的 iPhone(AirPods)配对,并检查它是否也连接到您的Apple Watch。当然,您也可以将AirPods直接连接到Apple Watch。两种方法产生相同的结果。
7. 更新您的 Apple Watch
watchOS 更新通常附带解决(watchOS updates)Apple Watch上关键连接和性能问题的错误修复。如果上述故障排除步骤均无法解决 AirPods 无法连接的问题,请更新设备的操作系统并重试。
将Apple Watch连接到 Wi-Fi 网络,前往“设置”(Settings) > “通用(General)” > “软件更新”(Software Update)并安装任何可用的更新。
让我们知道这些推荐技术中的哪些解决了您Apple Watch上的问题。同样(Likewise),如果您有任何问题或需要进一步的帮助,请发表评论。
AirPods Not Connecting to Apple Watch? Try these 7 Fixes
Connecting AіrPods to уour Apple Watch is the eaѕiest thіng ever. Yоu don’t have to do it manually. Your AirPods will automatically pair with your Applе Watсh if it’s already сonnected to your iPhone or iPad. However, there are times when things don’t work as they should.
If your AirPods are not connecting or pairing with your Apple Watch, try the troubleshooting checks listed in this article.
Before you proceed, ensure the AirPods is close to your Apple Watch. Also, confirm that the AirPods hold sufficient battery power. Otherwise, place both AirPods in the charging case and plug the case into a power source.
If your AirPods model supports wireless charging, and you have a wireless charger, place it on the charging pad for about 10 minutes. Try reconnecting the AirPods to your device after it charges for a bit.
1. Disable Airplane Mode
Having Airplane Mode enabled could prevent your AirPods from connecting to your Apple Watch. If there’s an airplane icon on your watch’s face or at the top of the screen, go to Settings > Airplane mode and toggle off Airplane mode.
You can also disable Airplane Mode from your Apple Watch’s Control Center. Press the Digital Crown to go to your watch’s face and swipe up from the bottom of the screen. Then, tap the orange airplane icon to disable Airplane Mode.
If you’ve previously paired the AirPods to your Apple Watch (check Settings > Bluetooth), it should connect to your device after disabling Airplane Mode.
To connect new AirPods, place them in the charging case and open the lid. Next, press and hold the setup button on the case to put it in pairing mode. Afterward, open the Settings app on your Apple Watch, tap Bluetooth and select the AirPods on the list of devices.
2. Re-Enable Your Apple Watch Bluetooth
If turning off Airplane Mode doesn’t fix the problem, disabling and re-enabling Bluetooth should. Open the Settings app, select Bluetooth, and toggle off Bluetooth.
Wait for a couple of seconds and toggle Bluetooth back on.
Proceed to the next solution if the AirPods still isn’t connecting to your Apple Watch.
3. Disconnect AirPods from Other Devices
You may be unable to pair AirPods to your Apple Watch if it’s in use by another device, particularly a non-Apple device. Disconnect the AirPods from your devices and try connecting it to your Apple Watch again.
On an iPhone or iPad, go to Settings, select Bluetooth, tap the info icon (🛈) next to the AirPods, and select Disconnect.
If the AirPods is hooked to your Mac, click the Bluetooth icon on the menu bar and click the AirPods’ name to disconnect it from your Mac.
If you use the AirPods on a Windows PC, go to Settings > Devices > Bluetooth & other devices and select the AirPods in the “Audio” section. Afterward, click the Disconnect button.
4. Forget the AirPods on Your iPhone or Apple Watch
Follow the steps below if a previously paired AirPods no longer connects to your Apple Watch. To do this, remove the AirPods from your iPhone or Apple Watch’s memory and re-pair the device.
Forget AirPods on Apple Watch
If your Apple Watch is paired to your iPhone, forgetting the AirPods on your watch will also remove the AirPods from your iPhone and other devices connected to your iCloud account.
- Open the Settings app on your Apple Watch and select Bluetooth.
- Tap the info icon (🛈) at the bottom-right corner of the AirPods’ name.
- Select Forget Device.
- You’ll get a confirmation prompt notifying you that removing the AirPods from your Apple Watch will also remove the AirPods from other devices connected to your iCloud account. Tap Forget Device to proceed.
Wait for 30 seconds to a minute and reconnect the AirPods to your Apple Watch.
- Place both AirPods in the charging case and open the lid. Press and hold the setup button at the back of the charging case until the status light blinks white.
- Open the Settings app on your Apple Watch, select Bluetooth, and select your AirPods on the list of available devices. Look out for a “Not Paired” status description below your AirPods’ name.
Alternatively, go to your watch’s face, swipe up from the bottom of the display, tap the AirPlay icon and select Connect a Device. That’ll redirect you to the watchOS Bluetooth menu.
- Wait till you see a “Connected” status description below the AirPods’ name.
Forget AirPods on iPhone or iPad
As mentioned earlier, removing the AirPods from your Apple Watch will also remove it from your iPhone or iPad. So you can either forget the AirPods directly from your Apple Watch or iPhone/iPad. It’ll yield similar results. If you choose the latter, here’s how to go about it:
- Open the Settings app on your iPhone or iPad, select Bluetooth, and tap the info icon 🛈 next to the AirPods.
- Scroll to the bottom of the AirPods menu and select Forget This Device.
- Select Forget Device on the confirmation prompt.
- Again, select Forget Device on the second confirmation prompt.
- To reconnect the AirPods to your iPhone or iPad, place both AirPods in the charging case and hold the setup button on the charging case until the light blinks white.
- You should see a setup animation at the bottom of your iPhone or iPad. Tap Connect to proceed.
If the AirPods setup animation doesn’t show up on your device, go to Settings > Bluetooth and select your AirPods in the “Other Devices” section.
5. Restart Apple Watch
Something isn’t working correctly on your Apple Watch? Restarting the device might fix the problem. Press and hold your Apple Watch’s side button and move the Power Off slider to the right.
Wait for about a minute for the device to shut down completely. Afterward, hold the side button until the Apple logo appears on the Apple Watch.
6. Unpair and Re-pair Your Apple Watch
Some users in this Reddit thread fixed issues with AirPods not connecting by unpairing their Apple Watches from their devices. Note that unpairing your Apple Watch restores it to factory settings. Interestingly, data from the Apple Watch is automatically backed up to your iPhone or iPad.
Follow the steps below to learn how to unpair your Apple Watch and restore your data when you reconnect the Watch to your device.
- Open the Watch app on your iPhone or iPad and go to the My Watch tab.
- Select All Watches at the top-left corner.
- Tap the info icon 🛈 next to your watch.
- Tap Unpair Apple Watch.
- Again, select Unpair Apple Watch on the confirmation.
- Enter your Apple ID password and tap Unpair to proceed.
Unpairing your Apple Watch from your device takes a while, so you might have to wait for a couple of minutes.
- To re-pair your Apple Watch, open the Watch app and tap the Start Pairing button.
Note: Make sure your iPhone/iPad and Apple Watch are nearby.
- Select Set Up for Myself if you’re pairing your personal Apple Watch or select Set Up for a Family Member if you’re setting up an Apple Watch for a family member who doesn’t own an iPhone or iPad.
- Align the viewfinder with the pairing animation on your Apple Watch and wait for about 2-5 seconds. That’ll pair both devices immediately.
- Since you’re re-pairing the watch to your iPhone, select Restore from Backup to recover your Apple Watch’s data.
- Select a backup from the list and tap Continue to proceed.
- Accept the usage terms and conditions and follow the prompt to set up the Apple Watch to your preference—create a passcode, set up Siri, adjust text size, personalize clock face, etc.
- Your iPhone will sync with your Apple Watch and restore your backup. Wait until you get a “Your Watch is ready” message on your Apple Watch’s screen.
Pair the AirPods with your iPhone and check if it also connects to your Apple Watch. Of course, you could also connect the AirPods directly to your Apple Watch. Both methods yield the same result.
7. Update your Apple Watch
watchOS updates often ship with bug fixes that resolve critical connectivity and performance issues on the Apple Watch. If none of the above-listed troubleshooting steps fix the problem with your AirPods not connecting, update your device’s operating system and try again.
Connect your Apple Watch to a Wi-Fi network, go to Settings > General > Software Update and install any available update.
Let us know which of these recommended techniques resolved the problem on your Apple Watch. Likewise, drop a comment if you have any questions or need further assistance.