安装Windows XP Service Pack 3并重新启动计算机后,有些人会收到此错误:
A problem has been detected and Windows has been shut down to prevent damage to your computer.
伴随该错误的一些技术代码是:OX0000007E (0XC00007D, 0XF7C6B8EA, 0XF7C6B7F4 – 0XF7CBBYF0)。通过启动到安全模式(Safe Mode),我注意到在加载MUP.SYS驱动程序时启动过程停止了。
首先要尝试的是从Windows XP安装 CD 启动并进入故障恢复控制台(按R键),然后执行chkdsk /r 检查。如果发现任何错误,它将尝试修复它们。扫描后,重新启动计算机并希望一切顺利。
如果上述方法不起作用,那么您需要尝试从正常工作的系统中复制MUP.SYS文件,然后将其粘贴到 C:windowssystem32drivers 文件夹中。
如果上述解决方案不起作用,请重新启动计算机并启动到Windows XP安装 CD,如上所示。
修复 安装 Windows XP
当您看到制造商徽标时,您必须按F12或 F2 或 F8 才能进入启动选项菜单。然后选择 CD 驱动器,而不是常规硬盘驱动器。这将带您进入如上所示的Windows XP设置。(Windows XP)
加载完所有文件后,您必须按照步骤安装 Windows。这意味着您按Enter而不是 R。
执行这些步骤,直到您必须同意条款和条件并看到一个屏幕,询问您在哪里安装Windows。它就像一张列出所有硬盘驱动器的表(大多数人都有 C,这是唯一的一个)。突出显示(Highlight)它,然后按相应的键安装Windows。安装开始时,Windows将检测到您已经在 [c] 驱动器/分区上安装了Windows的副本。(Windows)
它会询问您安装是否损坏,它可以尝试修复Windows XP安装。继续并按 R 键修复它。执行修复安装需要一些时间,您需要在安装过程中回答一些问题。
修复安装后,您的所有数据都应完好无损。希望(Hopefully)在重新启动后,Windows应该可以在没有任何蓝屏错误的情况下启动。如果您有任何问题,请随时发表评论。享受!
A Problem Has Been Detected and Windows Has Been Shutdown to Prevent Damages to Your Computer
After installing Windows XP Service Pack 3 and rebоoting the computer some people get this error:
A problem has been detected and Windows has been shut down to prevent damage to your computer.
Some of the technical codes accompanying the error are: OX0000007E (0XC00007D, 0XF7C6B8EA, 0XF7C6B7F4 – 0XF7CBBYF0). By booting into Safe Mode, I noticed that the boot process stopped when the MUP.SYS driver was loading.
The first thing to try is to boot from the Windows XP installation CD and get to the recovery console (by pressing R), then do a chkdsk /r check. If it finds any errors, it will try to repair them. After the scan, reboot the computer and hope for the best.
If the above does not work, then you need to try to to copy over the MUP.SYS file from a good working system and then paste it to the C:\windows\system32\drivers folder.
If the above solution does not work, restart the computer and boot up onto the Windows XP installation CD like shown above.
Repair Install Windows XP
When you see your manufacturer logo, you have to press F12 or F2 or F8 to get to the boot options menu. Then you select the CD drive, instead of the regular hard drive. This should bring you to the Windows XP setup like shown above.
When all the files are done loading, you have to follow the steps to install windows. This means you press Enter instead of R.
Go through the steps until you come to the point when you have to agree the terms and conditions and see a screen asking you where to install Windows. It’s like a table that has all your hard drives listed (most people have C, and that’s the only one). Highlight it, and press the appropriate key to install Windows. When the installation starts, Windows will detect that you already have a copy of Windows installed on your [c] drive/partition.
It will ask you if the installation is damaged, it can attempt to repair the Windows XP installation. Go ahead and press the R key to repair it. It will take some time to perform the repair install and you will need to answer some questions during the installation.
All your data should be intact after the repair install. Hopefully, upon reboot, Windows should boot without any blue screen errors. If you have any questions, feel free to comment. Enjoy!