如果您看到消息B200: Canon打印机上发生打印机错误(B200: Printer error has occurred),那么这篇文章将确定可能的原因,并提供您可以尝试帮助您解决此问题的最合适的解决方案。
当你遇到这个问题。您将收到以下完整的错误消息;
Error Number : B200
A printer error has occurred.
Turn the printer off and unplug the power cord of the printer from the power supply. Then contact the service center.
此错误通常是由于墨盒有问题而发生的。由于打印机打印头的问题,也会出现该错误。
B200:发生打印机错误
解决此错误的故障排除非常简单。由于佳能(Canon)打印机配备2 or 4+ cartridges,因此对B200 进行故障排除:发生打印机错误(B200: Printer error has occurred)对于这两种打印机来说是不同的。
如果是打印头,您可以尝试的一件事是卸下打印头并进行清洁。
因此,如果您遇到此问题,您可以按照以下有关墨盒和打印头故障排除的说明来解决问题。
排除 4+墨盒佳能(Cartridge Canon)打印机
- 打开打印机的顶盖。墨盒支架将自动抬起。从底座中取出所有墨盒。
- 下一步是卸下打印头,只需提起位于墨盒支架旁边的控制杆即可轻松完成。抬起控制杆后,只需轻轻地将打印头从打印机中取出。
- 在第三步中,将打印头重新插入打印机中的位置,并确保锁定杆。
- 然后将所有墨盒重新插入打印机中的正确位置,并确保没有打开的门。通过确保门关闭可确保打印机已准备好使用墨盒和打印头。
- 然后将您的打印机电源线从电源板上拔下,并将其拔下至少 5 分钟或更长时间。这导致打印机冷却,并且还消除了挥之不去的电能。
- 重新插入打印机。
在此过程之后,应该解决B200:已发生打印机错误的 问题。(B200: Printer error has occurred )
2墨盒佳能(Cartridge Canon)打印机故障排除
- 关闭打印机。墨盒底座实际上卡在错误 B200(Error B200)状态。但是,暂时重新调整打印机让我们进一步纠正错误 B200(Error B200)。
- 再次打开打印机。
- 错误 B200(Error B200)并不准确指示有问题的墨盒。因此,您应该大致了解上次更换的墨盒。从插槽中轻轻取出墨盒。
- 在 2 墨盒佳能(Canon)打印机中,打印机的打印头是墨盒的一部分。此打印机有一个限制,即如果不更换有问题的墨盒,您将无法防止错误 B200 。(Error B200)因此,请使用旧的可正常工作的墨盒更换墨盒或更换新墨盒。
- 进行广泛的喷嘴检查或清洁周期。更换墨盒后,这是确定是否从打印机更换所需墨盒的关键步骤。
- 如果问题仍未解决,则将另一个墨盒更换为新墨盒或旧墨盒。由于这台佳能(Canon)打印机使用 2 个墨盒,因此很明显两个墨盒中的任何一个都有故障。一个一个地更换和检查两个墨盒应该可以解决问题。
- 如果执行上述所有步骤对两种类型的佳能(Canon)打印机进行故障排除后问题仍然存在,则建议用户与佳能帮助热线(Canon Helpline)或打印机技术人员取得联系。
打印头故障排除
有关如何卸下打印头的详细说明,我们强烈建议您查看打印机手册。
清洁打印头后,请确保它完全干燥,然后再将其放回打印机中。还可以尝试使用提示和酒精清洁打印头连接器。
在打开打印机电源之前,请确保连接器完全干燥。我们还建议快速按下电源按钮以启动打印机的重启模式。
此外,重新安装打印头。重新安装打印头后,关闭打印机并让它关闭几分钟,然后再重新打开,看看B200:发生打印机错误(B200: Printer error has occurred )问题是否已解决。如果没有,您可以检查障碍物作为进一步的故障排除。为此,您需要关闭打印机电源、取出纸张并检查是否有任何障碍物。
如果发现任何障碍物,请将其移除并重新打开打印机。
Hope this helps!
相关帖子(Related post):对打印机进行故障排除时出现错误 0x803C010B。
B200: Printer error has occurred on Canon printers
Іf you’re seeing a message B200: Printer error has occurred on Canon printers, then this post will identify the possible cause, as well as provide the most appropriate solutions you can try to help you remediate this issue.
When you encounter this issue. you’ll receive the following full error message;
Error Number : B200
A printer error has occurred.
Turn the printer off and unplug the power cord of the printer from the power supply. Then contact the service center.
This error usually occurs due to problematic cartridges. The error can also appear due to problems with the printer’s printhead.
B200: Printer error has occurred
The troubleshooting for resolving this error is quite simple. As the Canon printers comes with either 2 or 4+ cartridges, so troubleshooting the B200: Printer error has occurred is different for both the printers.
If it’s the printhead, one thing that you can try is to remove your printhead and clean it.
So, if you’re faced with this issue, you can follow our instructions below on troubleshooting the cartridges and the printhead to resolve the issue.
Troubleshooting 4+ Cartridge Canon Printers
- Open the top cover of your printer. The cartridge cradle will automatically lift up. Remove all the cartridges from the cradle.
- The next step is to remove the printhead which can be easily done by lifting the lever which is located just beside the cartridge cradle. After you have lifted the lever, then just gently remove the printhead from the printer.
- In the third step, reinsert the printhead back into its position in the printer and make sure to lock the lever.
- Then reinsert all the cartridges into their correct positions in the printer and make sure that there is no open door. By ensuring the closure of doors assures that the printer is ready with access to the cartridges and printheads.
- Then physically unplug your printer cord from the electricity board and leave it unplugged for at least 5 or more minutes. This results in the cooling down of the printer and the lingering electrical energy are also eliminated.
- Re-plug the printer.
After this process, the B200: Printer error has occurred issue should be resolved.
Troubleshooting 2 Cartridge Canon Printers
- Turn OFF the printer. The cartridge cradle actually gets stuck in the Error B200 state. However, re-tuning the printer temporarily let us further rectify the Error B200.
- Turn the printer ON again.
- The Error B200 does not exactly indicate the problematic cartridge. Therefore, you should have a rough idea that which cartridge you replaced last. Remove that cartridge gently from the slot.
- In a 2 cartridge Canon printer, the printer’s printhead is the part of the cartridge. This printer has a limitation that you cannot prevent the Error B200 without replacing the problematic cartridge. Therefore replace the cartridge with an old functioning cartridge or replace it with a new one.
- Do an extensive nozzle check or a cleaning cycle. After the replacement of the cartridge, this is a critical step to determine whether the desired cartridge is replaced from the printer.
- If the problem is still unresolved, then replace the other cartridge with a new one or an old functioning cartridge. As this Canon printer works with 2 cartridges, so it is obvious that either of the two cartridges is faulty. Replacing and checking both cartridges one by one should resolve the problem.
- If the problem still persists after performing all the above steps for troubleshooting both types of Canon printers, then it is recommended to the user to get in touch with the Canon Helpline or a printer technician.
Troubleshooting the printhead
For detailed instructions on how to remove your printhead, we strongly suggest that you check your printer manual.
After you clean your printhead, make sure that it’s completely dry before you put it back in your printer. Also try to clean printhead connectors with cue tips and alcohol.
Before powering on your printer, be sure that the connectors are completely dry. We also suggest to press the power button rapidly to start the reboot mode on the printer.
Additionally, reseat your printhead. After reseating the printhead, turn off your printer and leave it turned off for a couple of minutes before you turn it back on and see if the B200: Printer error has occurred issue is resolved. If not, you can check for obstructions as further troubleshooting. To do so, you need to power down your printer, remove the paper, and check for any obstructions.
If any obstructions are found, remove them and turn the printer back on.
Hope this helps!
Related post: Error 0x803C010B while troubleshooting Printers.