尽管Windows 10为您的 PC 提供了最佳配置并自动检测适当的显示设置，但您需要确保正确校准显示器显示颜色。最好的部分是Windows 10实际上允许您使用特殊的向导校准显示颜色。此显示器颜色校准向导工具可改善显示器上照片、视频等的颜色，并确保颜色准确显示在屏幕上。

显然，显示颜色校准向导已深入Windows 10设置，但不必担心，因为我们将在本教程中介绍所有内容。因此，不要浪费任何时间，让我们看看如何在下面列出的教程的帮助下校准Windows 10中的显示器显示颜色。^{(Monitor Display Color)}

如何在Windows 10中校准^{(Windows 10)}显示器显示颜色^{(Monitor Display Color)}

确保 创建一个还原点^{(create a restore point)} 以防万一出现问题。

1. 您可以使用运行快捷方式或通过Windows 10 设置^(Settings)直接打开显示颜色校准向导。Press Windows Key + R然后键入dccw并按Enter以打开显示颜色校准^{(Display Color Calibration)}向导。

2. 按Windows Key + I 打开设置^(Settings)，然后单击系统。^(System.)

3. 从左侧菜单中，选择右侧窗格中的显示^{( Display)}，单击底部的“高级显示设置”链接。^{(Advanced display settings)}

4. 在监视器^(Monitor) 属性^(Properties)窗口下切换到色彩管理^{(Color Management)}选项卡，单击“色彩管理^{(Color Management)}”。

5. 现在切换到高级^(Advanced)选项卡，然后单击显示校准下的“校准显示^{(Calibrate display)}” 。^{(Display Calibration.)}

6. 这将打开显示颜色校准向导^{( Display Color Calibration wizard)}，单击下一步^(Next)开始该过程。

7. 如果您的显示器支持重置为出厂默认设置，请执行此操作，然后单击下一步^(Next)继续。

8. 在下一个屏幕上，查看 gamma 示例，然后单击 Next。^{(review the gamma examples, then click Next.)}

9. 在此设置中，您需要通过上下移动滑块来调整 Gamma 设置，直到每个圆圈中间的小点的可见度最小，然后单击^{(adjust the gamma settings)}Next。

10. 现在您需要找到显示器的亮度和对比度控件，^{(find the brightness and contrast controls of your display)}然后单击下一步。^(Next.)

注意：^(Note:)如果您使用的是笔记本电脑，您将无法控制显示器的亮度和对比度，因此请单击 ^{(click on )}跳过亮度和对比度调整^{(the Skip brightness and contrast adjustmen)}按钮。

11.仔细查看亮度示例，^{(Review the brightness examples carefully)}因为您将在下一步中需要它们，然后单击下一步。^(Next.)

12.如图所示，调高或调低亮度^{(Adjust the brightness higher or lower as described in the image)}，然后单击下一步。^(Next.)

13. 同样，查看对比示例^{(review the contrast examples)}并单击下一步。^(Next.)

14.使用显示器上的对比度控件调整对比度，^{(Adjust the contrast using the contrast control)}并按照图像中的说明将其设置得足够高，然后单击Next。

15. 接下来，仔细查看色彩平衡示例，^{(review the examples of colour balance carefully)}然后单击下一步。

16. 现在，通过调整红色、绿色和蓝色滑块来配置色彩平衡，以消除灰色条中的任何偏色，然后单击下一步。^{( configure the colour balance by adjusting the red, green, and blue sliders to remove any colour cast from the grey bars and click Next.)}

17. 最后，要将先前的颜色校准与新校准进行比较，请单击先前校准或当前校准按钮。^{(click the Previous calibration or Current calibration button.)}

18. 如果您发现新的颜色校准足够好，请选中“单击完成时启动 ClearType Tuner 以确保文本正确显示框^{(Start ClearType Tuner when I click Finish to ensure that text appears correctly box)}”，然后单击完成^(Finish)以应用更改。

19. 如果您没有找到符合要求的新颜色配置，请单击“取消^(Cancel)”以恢复到之前的配置。

受到推崇的：^{(Recommended:)}

• 在 Windows 10 中安装 CAB 文件的最简单方法^{(Easiest way to Install a CAB File in Windows 10)}
• 如何在 Windows 10 中启用或禁用自适应亮度^{(How to Enable or Disable Adaptive Brightness in Windows 10)}
• 禁用 Windows 10 更新的活动时间^{(Disable Active Hours for Windows 10 Update)}
• 在 Windows 10 中启用或禁用内置管理员帐户^{(Enable or Disable Built-in Administrator Account in Windows 10)}

就是这样，您已经成功学习了如何在 Windows 10 中校准显示器显示颜色，^{(How to Calibrate your Monitor Display Color in Windows 10)}但如果您对本教程仍有任何疑问，请随时在评论部分提出。

How to Calibrate your Monitor Display Color in Windows 10

Although Windows 10 comes with the best configuration for your PC and automatically detects the appropriate disрlay settings, you want to make sure that your monitоr display colour is correctly calibratеd. The best part is that Windows 10 actυally allows you to calibrate your display colour with a special wizard. This display colour calibration wizard tool improves the colours of уour photos, videos etc. on your display, and it ensures that thе coloυrs appear accurately on your screen.

Obviously, the display colour calibration wizard has buried deep into Windows 10 settings but didn’t worry as we would cover everything in this tutorial. So without wasting any time, let’s see How to Calibrate your Monitor Display Color in Windows 10 with the help of the below-listed tutorial.

How to Calibrate your Monitor Display Color in Windows 10

Make sure to create a restore point just in case something goes wrong.

1. Either you can directly open display colour calibration wizard using the run shortcut or via Windows 10 Settings. Press Windows Key + R then type dccw and hit Enter to open the Display Color Calibration wizard.

2. Press Windows Key + I to open Settings then click on System.

3. From the left-hand menu, select Display in the right window pane click “Advanced display settings” link at the bottom.

4. Under the Monitor Properties window switch to Color Management tab, click on “Color Management“.

5. Now switch to Advanced tab then click “Calibrate display” under Display Calibration.

6. This will open the Display Color Calibration wizard, click Next to start the process.

7. If your display supports reset to factory default, then do that and then click Next to proceed further.

8. On the next screen, review the gamma examples, then click Next.

9. In this setup, you need to adjust the gamma settings by moving the slider up or down until the visibility of small dots in the middle of each circle is minimum, and click Next.

10. Now you need to find the brightness and contrast controls of your display and click Next.

Note: If you’re on a laptop, you won’t have brightness and contrast controls of your display, so click on the Skip brightness and contrast adjustment button.

11. Review the brightness examples carefully as you would need them in the next step and click Next.

12. Adjust the brightness higher or lower as described in the image and click Next.

13. Similarly, review the contrast examples and click Next.

14. Adjust the contrast using the contrast control on your display and set it high enough as described in the image and click Next.

15. Next, review the examples of colour balance carefully and click Next.

16. Now, configure the colour balance by adjusting the red, green, and blue sliders to remove any colour cast from the grey bars and click Next.

17. Finally, to compare the previous colour calibration to the new one, click the Previous calibration or Current calibration button.

18. If you find the new colour calibration good enough, checkmark “Start ClearType Tuner when I click Finish to ensure that text appears correctly box” and click Finish to apply the changes.

19. If you don’t find the new colour configuration up to the mark, click Cancel to revert to the previous one.

Recommended:

• Easiest way to Install a CAB File in Windows 10
• How to Enable or Disable Adaptive Brightness in Windows 10
• Disable Active Hours for Windows 10 Update
• Enable or Disable Built-in Administrator Account in Windows 10

That’s it you have successfully learned How to Calibrate your Monitor Display Color in Windows 10 but if you still have any questions regarding this tutorial then feel free to ask them in the comment’s section.

Related posts

• 在Windows 10中更改Operating Systems的Time至Display List Startup

• Windows 10上的Fix Generic PnP Monitor Problem

• 在Windows 10中轻松Access Color And Appearance

• Windows 10中的Prevent Changing Color and Appearance

• Start Menu，Taskbar，Action Center和Windows 10的Change Color

• Allow or Prevent Devices在Windows 10中唤醒Computer

• 如何在 Windows 10 中更改任务栏颜色

• 如何禁用Windows 10 Firewall

• 如何在Windows 10上使用Performance Monitor（Detailed GUIDE）

• 如何在Windows 10中启用或Disable Emoji Panel

• 如何在Windows 10启用有源Directory

• Windows 10 User Find Security Identifier（SID）

• 如何在 Windows 10 中更改显示器刷新率

• Fix Keyboard未在Windows 10中键入

• 3 Ways在Windows 10中杀死A Process

• 如何在Windows 10上运行JAR Files

• 在Windows 10 Lock Screen上启用或禁用Cortana

• Fix Computer Wo在Windows 10中没有转到Sleep Mode

• Windows 10中的Defer Feature and Quality Updates

• 如何在 Windows 10 中检查显示器型号