如果您在尝试将大小超过 2 GB 的大文件复制到具有大量可用空间的USB 闪存驱动器或硬盘时收到错误“文件对于^{(USB Flash drive or Hard disk)}目标文件系统^{(destination file system)}来说太大”错误^{(” error)}，那么这表示您的闪存驱动器或硬盘^{(Flash drive or Hard disk)}使用FAT32 文件^{(FAT32 file)}系统进行格式化。

什么是 FAT32 文件系统？^{(What is a FAT32 File system?)}

早期版本的Windows，如Windows 95 OSR2、Windows 98和Windows Me使用更新版本的FAT（文件分配表^{(File Allocation Table)}）文件系统^{(file system)}。此更新版本的FAT称为FAT32，它允许默认的簇大小^{(default cluster size)}小至 4KB，并支持大于 2 GB的EIDE 硬盘大小。^{(EIDE Hard disk)}但在当前环境下，它们无法支持大文件大小^{(file size)}，因此已被NTFS（新技术文件系统^{(New Technology Files System)}）取代^{(file system)}从Windows XP开始的^{(Windows XP)}文件系统。

现在您知道为什么会收到上述错误，是时候知道如何修复此错误了。因此，不要浪费任何时间，让我们看看如何通过下面列出的故障排除步骤修复此错误。

该文件对于目标文件系统^{(destination file system)}来说太大[已解决]

确保^(Make)创建一个还原点^{(restore point)} 以防万一^{(case something)}出现问题。

方法一：将FAT32文件系统转为NTFS，不丢失数据^{(Method 1: Converting FAT32 file system to NTFS without data loss)}

1. 按Windows Key + X，然后选择命令提示符（管理员）。^{( Command Prompt (Admin).)}

2. 检查您的USB 闪存驱动器^{(USB flash drive)}或外部硬盘驱动器分配的字母是什么？^{( external hard drive?)}

3.在cmd中^{(cmd and hit)}输入^(Enter)以下命令并回车^(Enter)：

注意^(Note)：确保^{(Make sure)}将驱动器号^{(driver letter)}替换为您自己的设备驱动器^{(Device drive)}号。

Convert G: /fs:ntfs /nosecurity

4. 等待几分钟以完成转换过程^{(conversion process)}，因为这将需要一些时间，具体取决于您的磁盘大小^{(disk size)}。如果上述命令失败，则需要运行Chkdsk（检查磁盘^{(Check Disk)}）命令来修复驱动器。

5. 所以在命令提示符窗口^{(command prompt window)}中输入以下内容并回车：chkdsk g:/f

注意： 将^(Note: )驱动器号^{(driver letter)}从 g:更改为您自己的USB 闪存^{(USB flash)} 驱动器号^{(drive letter)}。

6. 现在再次运行Convert G: /fs:ntfs /nosecurity 命令，这次会成功。

7. 接下来，尝试早先在设备中复制大文件，出现错误“文件对于目标文件系统^{(destination file system)}来说太大。”

8.这将成功修复文件对于目标文件系统来说太大的错误^{( Fix The file is too large for the destination file system error)}，而不会丢失磁盘中的现有数据。

方法 2：使用 NTFS 文件系统格式化您的设备^{(Method 2: Format your Device using the NTFS file system)}

1. 右键单击​​您的USB 驱动器^{(USB drive)}并选择格式化。^{(select Format.)}

2. 现在将文件系统更改为NTFS（默认）。^{(NTFS (Default).)}

3. 接下来，在分配单元大小^{(Allocation unit size)}下拉列表中选择默认值。^(Default.)

4. 单击开始^(Start)，如果要求确认，请单击^{(confirmation click)}确定。

5. 让该过程完成^{(process finish)}并再次尝试将文件复制到您的驱动器。

推荐的：^{(Recommended:)}

• 修复程序^{(Fix Program)}链接和图标打开Word 文档^{(Word Document)}
• 如何 修复 Internet Explorer 11^{(Fix Internet Explorer 11)}无响应
• 修复^(Fix)Windows 10中无法连接^(Connect)到此网络问题^{(network issue)}
• 修复 Windows Live Mail 无法启动

就是这样，您已成功修复该文件对于目标文件系统来说太大^{(Fix The file is too large for the destination file system)}如果您对这篇文章仍有任何疑问，请随时在评论部分询问他们。

The file is too large for the destination file system [SOLVED]

If you are getting the errоr “Τhe file is too large for the destination file system” error when trying to copy a large file with size mоre than 2 GB to a USB Flash drive or Hard disk which have a lot of free space, then this means your Flash drive or Hard disk is formatted usіng the FAT32 file system.

What is a FAT32 File system?

The earlier version of Windows such as Windows 95 OSR2, Windows 98, and Windows Me used an updated version of the FAT (File Allocation Table) file system. This updated version of FAT is called FAT32 which allows for a default cluster size as small as 4KB and include supports for EIDE Hard disk size larger than 2 GB. But in the current environment, they cannot support large file size and therefore, have been replaced by NTFS (New Technology Files System) file system since Windows XP.

Now you know why you’re receiving the above error it’s time you should know how to fix this error. So without wasting any time, let’s see how to fix this error via the below-listed troubleshooting steps.

The file is too large for the destination file system [SOLVED]

Make sure to create a restore point just in case something goes wrong.

Method 1: Converting FAT32 file system to NTFS without data loss

1. Press Windows Key + X then select Command Prompt (Admin).

2. Check what letter is assigned to your USB flash drive or your external hard drive?

3. Enter the following command in cmd and hit Enter:

Note: Make sure to replace the driver letter to your own Device drive letter.

Convert G: /fs:ntfs /nosecurity

4. Wait for few minutes for the conversion process to complete as it will take some time depending on your disk size. If the above command fails, then you need to run Chkdsk (Check Disk) command to fix the drive.

5. So in the command prompt window type the following and hit Enter: chkdsk g:/f

Note: Change the driver letter from g: to your own USB flash drive letter.

6. Now again run the Convert G: /fs:ntfs /nosecurity command, and this time it would be successful.

7. Next, try copying large files in the device earlier, giving the error ‘The file is too large for the destination file system.’

8. This would successfully Fix The file is too large for the destination file system error without losing your existing data in the disk.

Method 2: Format your Device using the NTFS file system

1. Right-click on your USB drive and select Format.

2. Now change the file system to NTFS (Default).

3. Next, in the Allocation unit size dropdown select Default.

4. Click Start and if asked for confirmation click OK.

5. Let the process finish and again try to copy the files to your drive.

Recommended:

• Fix Program links and icons open Word Document
• How to Fix Internet Explorer 11 Not Responding
• Fix Can’t Connect to this network issue in Windows 10
• Fix Windows Live Mail won’t start

That’s it you have successfully Fix The file is too large for the destination file system if you still have any queries regarding this post feel free to ask them in the comment’s section.

Related posts

• USB Device不在Windows 10工作[求助]

• Windows 10中的Mouse Pointer Lags [已解决]

• Display driver停止响应并恢复错误[已解决]

• WiFi在Windows 10中断断开连接[已解决]

• Windows 10 Creator Update无法安装[已解决]

• Fix Windows Could不是Complete安装[解决]

• 帮助！颠倒或侧向屏幕问题[解决]

• 您当前的安全设置不允许下载此文件 [已解决]

• 启动时的Windows 10 Freezes [已解决]

• HDMI Port不适用于Windows 10 [已解决]

• Error 1962：未发现操作系统[已解决]

• 修复 Windows 10 中的键盘输入延迟 [已解决]

• WiFi 受限连接问题 [已解决]

• 默认打印机保持更改[已解决]

• Windows 10 上的 NVIDIA 安装程序失败错误 [已解决]

• Windows Update数据库损坏错误[已解决]

• Windows体验索引冻结[已解决]

• Fix Ethernet不在Windows 10中工作[解决]

• 数字小键盘在 Windows 10 中不起作用 [已解决]

• Action Center不适用于Windows 10 [已解决]